NEWS CENTER

新闻资讯

关注我们,即时了解最新动态

新闻资讯

  • 氢气发生器的使用注意事项
  • 本站编辑:上孰机电设备(上海)有限公司发布日期:2017-07-24 11:30 浏览次数:

1.启动前的准备 加氢氧化钾电解液(称取KOH100g溶解于1L的高纯水中),充分搅拌溶解等电解液完全冷却后再倒入储液桶中使用,然后加入高纯水不要超过上限水位线,也不要低于下限水位线,拧上外盖。液位管中的白色东西是液位管接口处的润滑剂,不影响使用,待整体换液后就好。

To prepare before the start of the 1. KOH electrolyte (called high purity water KOH100g dissolved in 1L), stirring dissolved electrolyte completely after cooling into the use of liquid storage barrel, then add high pure water do not exceed the limit water level line, not below the lower limit water level, twist the outer cover. The white thing in the level tube is the lubricant at the interface of the liquid level pipe. It doesn't affect the use of the liquid. It will be good after the whole liquid change.

2.装好后的溶液可以长期使用,每次快低于水位线时因立即加入高纯水,但加水需防止水漏在仪器内部造成短路,长时间不开机或长时间使用后电解液残渣积累较多时应更换电解液,正常情况下当仪器使用半年后,请更换电解液。更换电解液先要将储液桶内的电解液和残渣吸干净,再将仪器向前倾斜90度,此时电解池内的电解液就会流到储液桶内,接着用洗耳球或移液管把桶内的电解液吸干净,同时注意溶液流到其他管路上造成管路腐蚀。

2. installed after the solution can be used for a long time, every time below the water line when immediately joined the high water, but the water to prevent water leakage caused by a short circuit in the instrument, long time no boot should replace the electrolyte after a long time accumulation or electrolyte residue, under normal circumstances, when the instrument used for half a year, please replace the electrolyte. The first will replace the electrolyte in the liquid storing tank of the electrolyte and the residue suction clean, then the instrument is tilted 90 degrees forward, the electrolyte within the cell will flow into the liquid storage barrel, then wash the ear with a ball or a pipette to electrolyte barrel suction clean, while paying attention to other pipeline caused by the flow of solution pipeline corrosion.

201708181446256262.png

3.仪器的自检 打开电源开关,关闭净化器的气流开关,此时仪器压力表开始上升,检查仪器面板上电解指示(绿灯)发亮,数字流量显示(数显表)应大于300小于350,在6分钟内压力指示(压力表)应达到0.4MPa,然后数字流量显示降至“000”,说明仪器系统工作正常,自检合格。

3. instruments turn on the power switch, switch off air purifier, the instrument pressure began to rise, check the instrument panel indicating electrolytic (green) shiny, digital flow display (DRO) should be greater than 300 and less than 350, indicating the pressure in 6 minutes (pressure meter) should reach 0.4MPa, then to display digital flow "000", it shows that the instrument system is working properly, self qualified.

4.如在5分钟后,流量指示还在“300”左右,压力指示在“0”,说明开关没有旋紧有漏气现象,请继续旋紧开关,使仪器的压力、流量达到合格标准。若依旧如此需打开外盖用肥皂水检查各处旋钮的螺母,对漏气开关旋紧,直到仪器进入正常工作状态。

4., such as in 5 minutes after the flow instructions are still "300" or so, the pressure indicated in "0", indicating that the switch is not tightened, there is a leak phenomenon, please continue to tighten the switch, so that the instrument pressure, flow rate to meet the standards. If still the case, you need to open the lid, use the soapy water to check the nut of the knob, tighten the leak switch until the instrument enters the normal working state.

5.仪器使用时应注意流量指示是否与色谱仪用气量一致,如流量指示超出色谱仪实际用量较大时,应停机检漏,其方法参照仪器的故障原因与排除方法进行调整,再用自检方法检查合格后方可使用。

5. instrument use should pay attention to whether gas flow indicator is consistent with the chromatograph, such as flow directions beyond the actual chromatograph amount is larger, should stop the leak detection, fault methods according to instrument adjustment and troubleshooting, and self checking method checks before use.

6.定期检查过滤器中的硅胶是否变色,如变色请马上更换或再生。其方法为,拧下过滤器,再拧开过滤器上盖,更换硅胶后拧紧过滤器上盖,将过滤器装到底座上拧紧。并检查是否漏气。

6. regularly check whether the silica gel in the filter changes color, such as discoloration, please immediately change or regeneration. The method is to unscrew the filter, then unscrew the upper cover of the filter, replace the silica gel, tighten the filter upper cover, and then mount the filter to the bottom seat to tighten. And check for leaks.

7.仪器切勿在压力为“0”时空载运行。空载运行时会将电解池和开关电源部件烧坏,造成整个仪器损坏。

7., the instrument must not run at the pressure of "0" time and space.  When running without load, the electrolytic cell and the switch power supply parts will be burned out, resulting in damage to the whole instrument.

8.如发现压力表指示的压力低或数码显示比平时大时,一般说是由漏气造成的,应用皂液全面检漏。尤其是重新更换变色硅胶时,更应特别注意上下螺纹密封圈处不要挤压异物。

8., if you find that the pressure indicator indicates low pressure or the digital display is larger than usual, it is generally caused by leakage. In particular, when you replace the discolored silicone, you should pay more attention to the upper and lower thread sealing rings, do not squeeze foreign bodies.